Nova 23067 Manuale di Manutenzione e Cura

SUPERNOVA2™ GEARED CHUCK MANUAL READ THIS MANUAL CAREFULLY AND BECOME THOROUGHLY FAMILIAR WITH CHUCK OPERATIONS BEFORE USE Teknatool Internati

10MOUNTING JAWS The standard SuperNova2Chuck is provided with either 50mm or 75mm add-on jaws. They need to be located and screwed on to the jaw slid

11shanks are aligned to the jaw slides and close jaws around it. BEFORE FINAL TIGHTENING MAKE SURE THAT THE FRONT OF THE BOSS SECTION OF THE SCREW IS

12 For smaller lids and thin platters (not exceeding 150mm diameter) only a shallow recess of around 3mm (1/8 inch) is necessary. It will be a matter

13SPIGOT OPERATION This is where the jaws contract around a wooden spigot for grip. This function is mainly for box, goblet and vase turning, that is

14TROUBLE SHOOTING GUIDE FAULT REMEDY 1. Insert jams when partially threaded into body Check insert thread and chuck body thread are free from dam

15 10. Wooden spigot shifts during turning Check that the spigot area is made correctly for jaws to grip. Check that the spigot is not oversize. S

16SuperNova2 Chuck Maintanence This guide covers all steps, beginning from when your chuck is on the lathe; you may wish to skip several steps in ord

17Using a 1½” spanner (like accessory 23014 pictured) undo the insert from the wood lathe. Make sure that the spindle lock on the lathe is engaged an

18Screw in any Teknatool insert in the chuck thread. Engage the thread partially and tap on the back of insert with a mallet. You will see that the b

19Re-grease the scroll ring and pinions; be very generous with grease application. (Normal multi purpose grease is sufficient) If possible before re-

2WELCOME Thank you for purchasing our Teknatool SuperNova2 Geared Chuck. We are confident it will help to both enhance and advance your woodturning

20 Showing circlip snapped closed Place the circlip back on using the circlip pliers, you’ll see that once the circlip is in its groove the two end

21SUPERNOVA2 OPTIONAL ACCESSORIES The SuperNova2 Chuck is one of the most versatile chucking systems. It is fully compatible with the Nova Chuck, Sup

22100MM JAW SET Code: JS100N Have an expanding dovetail grip, strong reverse dovetail grip for footed bowls. Made for a larger range of work than eit

23 INSERT SPANNER Code: 23014 Spanner to remove inserts off lathe spindle. Other Accessories: Woodworm Screw RH & LH versions, Woodworm screws

24 WARRANTY Your serial number is shown on your printed SuperNova2 Quick Start Manual Sheet. For your future reference, record your serial number an

25 Teknatool International Ltd www.teknatool.com Publication Code: 106-0313-004

3CONTENTS SAFETY Rules 4 Models 5 Exploded Drawing & Parts List 6 Chuck Operation 7 Mounti

4YOUR SAFETY IMPORTANT PLEASE READ & UNDERSTAND THIS INFORMATION BEFORE USING YOUR SUPERNOVA2 CHUCK DANGER: THIS CHUCK IS CAPABLE OF CONTRIBUT

5• USE THE RIGHT CHISEL FOR THE JOB AND DO NOT FORCE TOOLS. Use safe and commonly approved chisel techniques. Wherever possible stand to one side of

6SUPERNOVA2 CHUCK EXPLODED DRAWING & PARTS LIST ITEM NO.QTY. PART NO. DESCRIPTION1 1 23049 Body SuperNov a 22 2 23045 Machined Cast Pinion3 1

7CHUCK OPERATION Adjustment: A handled chuck pinion key is provided for adjustment of chuck action. Please refer to the exploded drawing on page 6

8MOUNTING CHUCK ON LATHE There are two versions of the SuperNova2Chuck: an insert version for all threads up to 27mm (1 1/8”) and threaded versions

9damage) and screw in insert using the optional accessory spanner or a 1 1/2” AF spanner. Care needs to be taken that the outer male insert thread i